Does pallet racking need to be certified: loaded pallet racking with orange beams in a building materials warehouse

Does Pallet Racking Need to Be Certified? What OSHA, Code and RMI Say

Pallet racking doesn’t need an OSHA certification, but the building code, your city’s permit rules and ANSI MH16.1 set real requirements. Here’s what’s required, what’s voluntary, and who signs off.

  • 0
  • 10
  • 0
  • 10

CONTENTS

    Not Sure How This Applies to Your Business?

    icon blcok
    503-640-5666

    or

    No. U.S. law doesn’t require a certification for the pallet rack itself, and OSHA doesn’t certify equipment. What the law does require comes from your building code: racks designed to ANSI MH16.1, a permit above your city’s height limit, stamped engineering at 8 feet in many cities, and a certificate of compliance for racks 8 feet or taller in Seismic Design Categories D to F.

    Key Takeaways

    • OSHA doesn’t test, approve or certify racks, so there’s no such thing as an OSHA-certified pallet rack. 
    • The building code requires steel storage racks to be designed, tested and used to ANSI MH16.1. 
    • Racks 8 feet or taller in Seismic Design Category D, E or F need a certificate of compliance and special inspection. 
    • R-Mark is a voluntary RMI program that certifies the manufacturer, not your installed rack. 
    • After damage, a registered design professional must certify the repair before the rack is loaded again. 

    You have two quotes for the same rack. One says “certified racking” in bold, the other doesn’t mention it. Or the building inspector asks for a certificate of compliance and nobody on site has heard of one. Either way, you need to know whether pallet racking needs to be certified, and by whom.

    “Certified” gets used for four different things: the rack product, the installer, the inspection and the permit paperwork. Some of those are voluntary. Some are required by your building code. One is required by OSHA, but it’s about your forklift drivers, not your racks.

    This guide sorts them out: what OSHA does and doesn’t do, what the building code requires before you get a warehouse racking permit, what R-Mark means, and when an installation, inspection or repair needs a sign-off.

    Does Pallet Racking Need to Be Certified?

    No, not as a product. No federal law requires a certification for pallet racking. But several sign-offs around your racks are required, and the table shows which.

    What “certified” can meanRequired?Who signs off
    The rack product itselfNo. It must be designed to ANSI MH16.1 under the building codeRack manufacturer or engineer
    Engineering for the permitOften, at 8 feet and taller (your city decides)Engineer licensed in your state
    Certificate of complianceYes, for racks 8 feet or taller in Seismic Design Category D, E or FSubmitted to the owner at completion
    R-MarkNo, it’s voluntaryRMI, after independent engineering review of the manufacturer
    Repair after damageYes, before the rack is loaded againRegistered design professional
    Forklift operatorsYesThe employer, under OSHA 1910.178

    Does OSHA Certify Pallet Racks?

    No. OSHA has said plainly, in its own interpretation letters, that it does not test, approve, certify, or endorse any equipment, and that it has no legal authority to evaluate and certify manufacturers’ products. A rack sold as “OSHA certified” or “OSHA approved” is using a label OSHA doesn’t issue.

    What does OSHA require instead?

    OSHA regulates the workplace, not the product. For racks, that comes down to three rules:

    • Secure storage. 1910.176(b) requires stored material to be stable and secure against sliding or collapse. 
    • Recognized hazards. The General Duty Clause covers hazards no standard names, such as a damaged upright or an unanchored column. 
    • Forklift operators. Under 1910.178(l)(6), the employer must certify that each operator has been trained and evaluated. This is the only OSHA certification near your racks, and it certifies people, not equipment. 

    For the full OSHA breakdown, see our guide to warehouse racking requirements.

    What Does the Building Code Require for Pallet Racking?

    The building code is where the real requirements live. Most U.S. jurisdictions follow the International Building Code (IBC), sometimes with local changes, and its Section 2209 covers steel storage racks.

    Does pallet racking have to meet ANSI MH16.1?

    Yes. IBC Section 2209.1 requires steel storage racks to be designed, tested and used in line with ANSI MH16.1, the rack standard written by the Rack Manufacturers Institute (RMI). Cantilever racks follow ANSI MH16.3. You won’t get a certificate for meeting MH16.1, but your permit engineer designs to it and your building inspector checks against it.

    When does racking need stamped engineering?

    Your city sets the height. Many cities require a building permit once racks pass 5 feet 9 inches, and engineering at 8 feet. Some examples:

    • Portland and Springfield, Oregon; Fresno and Dublin, California: racks 8 feet and taller need engineered design and calculations stamped by an engineer licensed in your state. 
    • Vancouver, Washington: racks 8 feet or taller need site-specific structural engineering with a PE stamp, owner-provided third-party special inspection and a certificate of compliance, according to the city’s storage rack permit handout. 

    At Parr Lumber in Damascus, Oregon, the facility’s high-piled storage occupancy required full structural engineering and a permit before installation. Our structural engineer of record signed and sealed the calculations and permit drawings to Seismic Design Category D, and the system passed final building inspection with the note “Racking appears per plan.”

    What is a certificate of compliance for storage racks?

    It’s the one place the code actually uses the word “certification.” Under IBC Section 2209.3, racks 8 feet or taller to the top load level in Seismic Design Category D, E or F need a certificate of compliance at completion. It goes to the owner and states that the work was done according to the approved construction documents.

    The same racks also need periodic special inspection, including the anchors, under Section 1705.13.7, as the California Building Code lays out. Keep the certificate with your permit records. Your engineer confirms your Seismic Design Category during the seismic calculations. Our guide to pallet rack seismic compliance covers the rest of the seismic side.

    Do racks need a load capacity plaque?

    Yes. ANSI MH16.1 requires load capacity plaques that show what each beam level and bay can hold. They’re not a certification, but an inspector will look for them. We stock pallet rack capacity labels.

    What Is R-Mark Certification, and Do You Need It?

    R-Mark is RMI’s voluntary certification program. A manufacturer earns it by showing that it can design, manufacture and install storage rack systems that comply with ANSI MH16.1 (pallet rack), MH16.3 (cantilever) or MH26.2 (rack decking).

    To qualify, manufacturers submit sample designs for independent engineering review. According to RMI, certified manufacturers now also confirm every year that nothing has changed that would affect compliance, and must show their products still comply when the standard is revised.

    Keep three things in mind:

    • It’s voluntary. No code or OSHA standard requires R-Mark. 
    • It certifies the manufacturer, not your rack. An R-Mark doesn’t replace your permit, your engineering or your inspections. 
    • You can check it. RMI publishes the list of R-Mark certified companies, with the standards each one is certified to.

    Do You Have to Be Certified to Install Pallet Racking?

    OSHA’s storage rule, 1910.176, doesn’t include an installer certification. What gets checked is the installed work, not the crew’s card:

    • The rack goes in according to the manufacturer’s instructions and, where a permit applies, the approved drawings. 
    • For racks 8 feet or taller in Seismic Design Category D, E or F, a special inspector checks the installation, including the anchors. 
    • RMI recommends that installation inspections be done by a licensed, qualified rack engineer, who checks the installation against the load application and rack configuration (LARC) drawing. 
    • Where a permit applies, the racks can’t be loaded until the final building inspection passes. 

    Our pallet rack installation crews handle the installation and the inspection steps as part of the permit.

    Does Pallet Racking Need to Be Inspected?

    Yes, though the requirement comes from RMI guidance and OSHA’s general rules, not a federal inspection certificate. RMI puts the responsibility on the rack owner.

    How often should pallet racking be inspected?

    RMI recommends regular, routine inspections at least once a year, and more often where inventory moves fast or forklift traffic is heavy. Check the anchors, base plates, columns, bracing, beams and connections, and decking, and inspect again right after any forklift impact or earthquake. Our pallet rack inspection checklist walks through each part.

    A professional rack safety inspection gives you a written record. For Evraz in Portland, two of our managers spent four days checking the racking part by part, marked each rack green, yellow or red, and replaced every red-tagged rack, as described in the Evraz case study. The same rules apply to shared spaces, such as people who work under pallet racking.

    Does a damaged rack need to be re-certified?

    Yes. ANSI MH16.1-2023, as quoted by RMI, says the owner must immediately isolate the damaged section and start a repair or replacement. Before the rack goes back into service, a registered design professional must certify that it’s restored to at least its original design capacity.

    For severe damage, that means unloading the bays next to the damaged frame and taping off the area until the engineer approves the fix, such as an engineered repair kit.

    Does Used or Relocated Racking Need New Certification?

    Often, yes, because a move or reconfiguration is treated like new work. Vancouver’s handout says reused racks in a new location must meet current IBC loading criteria.

    The permit engineer needs the rack’s specs to calculate its capacity at your site, so old racks with unknown specs can be hard to permit. Ask the seller for these before you buy:

    • The manufacturer’s name 
    • Frame and beam specs (size, gauge, capacity) 
    • Original drawings or engineering calculations, if any 
    • The load capacity plaques

    Pallet Rack Certification FAQs

    Does pallet racking need to be certified in California?

    There’s no state certification for the rack product. The California Building Code carries the same Section 2209 rules: racks designed to ANSI MH16.1, and a certificate of compliance for racks 8 feet or taller in Seismic Design Category D, E or F. Fresno and Dublin also require plans and calculations signed by a California-licensed engineer at 8 feet and taller.

    Is R-Mark certification required by law?

    No. R-Mark is a voluntary program run by the Rack Manufacturers Institute. It shows a manufacturer can design, make and install racks to ANSI MH16.1, but no building code or OSHA standard requires it.

    Does OSHA require pallet rack inspections?

    OSHA has no standard that sets a rack inspection schedule. It does require stored material to be stable and secure under 1910.176(b), and RMI recommends an inspection at least once a year, plus a check right after any impact or earthquake.

    Does pallet racking need to be bolted down?

    In practice, yes. ANSI MH16.1 calls for a base plate on every column, and RMI says pallet rack columns should be anchored to the floor. The building code adopts MH16.1, so your city inspector will check the anchors.

    What Should You Do Next?

    Pallet racking doesn’t need a product certification, and OSHA doesn’t certify racks. What matters is what your building code and city require: ANSI MH16.1 design, a permit and stamped engineering above your local height limits, and a certificate of compliance for taller racks in high seismic areas. And after damage, an engineer has to certify the repair before the rack is loaded again.

    Planning new racks? Start a rack permit with our team, and we’ll price the layout, engineering, permit work and installation together. Already have racks up? Book a safety inspection or call 503-640-5666.

    Was this helpful?

    Contents

      Need a free consultation?

      icon blcok
      503-640-5666

      or

      Have any
      more questions?

      Call us

      Subscribe

      to our newsletter

      be informed

      about offers & solutions