Workers spend three minutes locating the right bundle because nothing is labeled. None of that is a rack problem. It’s a rack accessories problem.
This guide is for warehouse managers, operations directors, and facilities leads who already have cantilever racking installed and want to know exactly what to add and what each addition actually prevents.
New to cantilever racking and not sure where to start? We offer free assistance. Just give us a call on 5036405666, and we’ll tell you exactly what you need. Already know what you’re looking for? Use our cantilever rack builder to configure your system in seconds. If you have racking and it’s underperforming, keep reading.
More Arms Don’t Mean More Rack, They Mean More Capacity on What You Have
Adding arms to an existing cantilever upright is the fastest way to increase storage without touching your footprint. For a lumber yard, steel distributor, or plumbing contractor working inside a fixed building, vertical capacity is often the only capacity available.
Before you order additional arms, check how much of your upright’s 11,600 lbs column capacity is already committed to existing arm levels.

The number that matters most is the upright capacity, not the arm rating. You may have room to add arms physically. The upright may not be able to support your material weight.
The mistake buyers consistently make: they order additional arms based on available physical space, ignoring the upright’s remaining column capacity. You may have room to bolt on four more arms. The upright may support only two more at your material weight. Check the column capacity first, not after the arms arrive.
If you’re not sure what headroom your uprights have left, Speedrack West can pull that from your original order or assess it during a setup review.
Wire Mesh and Solid Steel Decking

You may come across wire mesh or solid steel decking for cantilever arms when researching online. It exists, but it’s uncommon. Cantilever racks are designed for long, bulky, and heavy products. If your inventory doesn’t fit that profile, a pallet rack is likely the better solution to begin with.
Guard Rails and Bollard Posts Stop Forklift Damage Before It Starts
A forklift impact at the base of a cantilever upright can compromise that column’s load rating without any visible cracking. That’s the scenario nobody catches until something fails under load.
Guard rails and bollard posts are the two products that prevent this. Guard rails define the boundary between forklift travel paths and rack positions. Bollard posts anchor at the floor and absorb direct impact before it reaches the upright.

Where to place them first:
- End caps at the mouth of every aisle
- Upright bases within reach of any forklift travel path
- Tight-turn zones near loading dock entries where operator sightlines are limited
The cost comparison is not close. A bollard post or guard rail costs a fraction of an upright replacement. An upright replacement costs a fraction of a workers’ compensation claim. These accessories are not optional safety theater; they’re the cheapest line of defense in the facility.
Are you not sure?
If you have a specific application in mind that requires decking on cantilever arms, call us before ordering anything. It’s a custom configuration, and we’ll want to understand your setup before recommending it.
Stop Pins Prevent the Most Common Cantilever Incident
Pipe, conduit, rebar, lumber, steel bar, or any long material that can roll will roll off an arm if nothing stops it. Cantilever stop pins are the direct fix. They drop into a 1.25″ receptacle at the end of each arm and extend approximately 10″ above the arm surface, creating a physical barrier that keeps material on the rack.

Installation is drop-in. Removal is tool-free. There’s no reason to run an arm without them when you’re storing anything that can shift or roll.
The load containment principle extends beyond the arm end. Every path a load can take off the rack needs to be accounted for. That includes the end, the sides, and the face. On any arm that stores heavy or shifts material, each of those paths is a real risk.
Stop pins address the end. For lateral containment, the answer isn’t a named product; it’s an engineering question about arm spacing, load width, and whether material is being stacked beyond the arm’s rated surface. If you’re unsure whether your current setup creates a lateral fall risk, that’s worth a direct conversation before something moves.
Consolidated Supply, a plumbing and waterworks distributor that Speedrack West works with, put the safety decision plainly:
“We want everybody to come in and go home with all their fingers, toes; come in and leave the same way they came. That’s another reason why we went with the racking we did, because it holds up and we don’t have to worry about it collapsing or parts falling on people.”.
Stop pins are a $10 decision that sits between that outcome and a recordable incident.
Load Capacity Labels Do More Than Satisfy an Inspector
Every cantilever rack installation should have load-capacity labels posted on the rack. This isn’t a recommendation; under OSHA, employers are required to maintain safe load limits on storage equipment, and visible capacity labels are how that requirement gets documented in practice.

But the operational case is just as strong as the compliance case. In a busy plumbing distributor’s yard or an electrical contractor’s warehouse, workers loading arms without knowing the rated capacity will overload them. Not out of carelessness, but out of the absence of information at the point of loading.
How to Know What Your Setup Is Actually Missing?
Three questions narrow the list fast.
What am I storing?
Long, round materials like pipe, conduit, and rebar require stop pins on every arm. Loose or smaller items need decking. Heavy non-standard loads need solid steel decking and column protection at every forklift approach point.
How is it loaded?
Forklift loading means guard rails and bollard posts at every entry point. Hand loading means decking and labeling matter more.
What’s already gone wrong?
Forklift damage history points to guard rails and bollard posts. Load fall-off incidents point to stop pins. Missing or incorrect capacity information points to load capacity labels.
If you’ve answered all three and still aren’t sure what your system needs, the problem is usually visible in the layout, not the product list.
Not Sure What Your Cantilever Rack Is Missing?
Speedrack West works with distributors, manufacturers, and contractors across the country to identify exactly what a cantilever system needs, based on load type, forklift traffic patterns, and the specific risks in your facility.
Something Off With Your Cantilever Rack?
If your cantilever racking is underperforming or you’re not confident it’s set up safely, a setup review costs nothing and takes less time than another incident report.
Was this helpful?











































